Best Cabinet Pulls & Shelf Hardware (2026)
By Nate Sawyer, Editor · Updated July 2026
DIYPicks is reader-supported. As an Amazon Associate and affiliate of home-improvement retailers, we may earn a commission when you buy through links on our site — at no extra cost to you. This never affects our recommendations.
Cabinet pulls are the jewelry of a kitchen: they are cheap relative to the whole remodel, but the wrong size or a mismatched hole spacing turns a quick upgrade into a day of filling and re-drilling. The key spec is center-to-center: the distance between the two screw holes, which must match your existing drilled holes or your new drawer-front template. Bar pulls in the 3 to 4 inch center range suit most doors and small drawers, while wider 5 inch pulls balance big pot drawers. We cover a designer solid pull, a value 10-pack bar pull, and a bulk 30-pack so you can do a whole kitchen without mixing finishes or paying boutique prices per handle.
Amerock's Blackrock pull uses the mainstream 96mm center-to-center spacing, so it lines up with most modern bored doors and drawers, and its solid zinc die-cast feels substantial in a broad finish range, with screws included. But die-cast zinc can chip on tile, 96mm won't fit fronts pre-bored for 76mm, and the screws may be short for thick fronts.
- Kitchen reno
- Modern look
- Drawers
- Doors
Pros
- 96mm center-to-center is the most common modern spacing, so it lines up with existing bored doors/drawers
- Solid zinc die-cast feels substantial, not hollow, and the finish range matches most kitchen palettes
- Comes with the mounting screws and a widely available collection so you can add matching sizes later
Cons
- Die-cast zinc can chip to bright metal if dropped on tile during install
- 3-3/4 in spacing won't fit doors pre-bored for 3 in (76mm) without re-drilling and filling old holes
- Included screws are one length — thick drawer fronts or backer plates need longer screws bought separately
A value 10-pack of straight bar pulls at the popular 4 in center-to-center spacing, aimed at anyone refreshing a kitchen who wants every handle to match without paying boutique prices. The clean bar profile suits modern and transitional cabinets, mounting hardware is included, and buying by the ten-pack keeps the per-pull cost low, though the fixed hole spacing must line up with your cabinets.
- Cabinet doors
- Kitchen refresh
- Value multipack
Pros
- Ten matching pulls in one box make it easy and affordable to redo a run of cabinets without mixing finishes
- Popular 4 in center-to-center fits many standard cabinet doors and mid-size drawers
- Simple, versatile straight-bar look pairs with both modern and transitional kitchens, and mounting screws are included
Cons
- Fixed 4 in hole spacing must match your existing holes, or you will need to fill and re-drill
- Lighter-weight build than solid designer pulls, so it feels less substantial in the hand
- A single bar length may look undersized on very wide pot-and-pan drawers that suit a longer pull
A bulk 30-pack of 5 in stainless steel bar pulls at 3 in hole center, built for doing an entire kitchen in one shot with a guaranteed matching finish. The solid stainless build resists rust, and both short and long screws are included to fit thin doors and thick drawer fronts, making it a strong per-pull value as long as the 3 in spacing matches your cabinets.
- Whole kitchen
- Drawers
- Bulk value
Pros
- A 30-pack covers most of a kitchen in one purchase, guaranteeing a consistent finish across every door and drawer
- Solid stainless steel construction resists rust and feels sturdier than hollow budget pulls
- Includes both short and long mounting screws, so it works on thin doors and thick drawer fronts alike
Cons
- 3 in hole center must match your existing drilled holes or new template, or you will need to re-drill
- 5 in overall length can look large on very small cabinet doors
- Buying 30 at once is wasteful and less economical if you only need a handful of pulls
Frequently Asked Questions
- What is center-to-center on a cabinet pull?
- Center-to-center (also called hole center or CC) is the distance between the middle of the two mounting screw holes. It must match the holes already drilled in your doors and drawers, or the new template you drill. It is different from the pull's overall length, which is always longer than the CC measurement.
- How many cabinet pulls do I need for a kitchen?
- Count every door and drawer that opens: doors usually get one pull or knob, and drawers get one pull (wide drawers sometimes two). A typical kitchen lands around 25 to 40 pieces, which is why buying a 10-pack or a 30-pack in one finish is cheaper and guarantees they all match.
- What size pull should I use on doors versus drawers?
- A common guide is a 3 to 4 inch center pull or a knob on cabinet doors and smaller drawers, and a longer 5 inch or larger center pull on wide drawers so the pull looks balanced and spreads the pulling force. Many people mix knobs on doors with bar pulls on drawers for a classic look.